Produse pentru pentru aer (58)

Druckluftwerkzeug

1.0 Cubic Inch Volume Tank See Catalog: Page 65 Additional Information Max PSI 250 PSI Medium Air Ports 1/8 NPT Temperature Range 30 F to 250 F

Kondensatableiter

4.0 Cubic Inch Volume Tank See Catalog: Page 65 Additional Information Max PSI 250 PSI Medium Air Ports 1/8 NPT Temperature Range 30 F to 250 F

Druckluftanschlüsse

Öl-Wasser-Trenner

Zubehör

The STR-1-15L22 is a transformer fan speed controller with which you can manually regulate the fan speed of single-phase motors in 5 steps. The unit also has an off-position. It needs a 230 VAC/50-60 Hz supply voltage and has an unregulated output of 230 VAC that can control a damper, an external status indicator, etc. This output is active as soon as the motor is enabled. The sinusoidal shape of the generated motor voltage results in an exceptionally quiet motor operation and extended service life. The special impregnated coating reduces the electrical noise from the built-in autotransformer. This series is available in different amperes. The casing of the controllers up to 7,5 A is made from high quality plastic, while the models above 7,5 A have a metal housing. This transformer doesn't need any configuration. Once installed, it's ready for use.

Combi 1.1 – Innovating product – Better and cheaper than Laminar Flow – Adjustable Air Nozzles for perfect airflow – Creates high efficiency Cleanroom Class ISO6 or even ISO5 – Installation: 1 day max. – Results within 30 minutes – Clean Air Capacity: 800 m3/hour maximum, with 1/4 of fresh air (optional) – Only needs W 90 cm x H 154 cm x D 34 cm of wall space – Quiet operating level – Max. distance between inside & outside unit: 25 meter To protect immune compromised patients To upgrade ICU’s, laboratories and O.T’s Note Pressure difference depends on air tightness of the room. For information and advice contact MedicCleanAir.

Druckluftschläuche

This control unit has two 0-10 Volt outputs to regulate the EC fans. Via the 2 tacho inputs you can directly monitor the status of the fans and their speed, if tacho signals are available on the fans. HVAC sensors or potentiometers can be connected to the unit, via Modbus RTU communication or 2 analogue inputs. The built-in 24 VDC power supply can feed the external sensors or potentiometers. The controller itself needs a supply voltage between 85 - 305 VAC. Application specific firmware is needed for the unit to function. This firmware can be downloaded via Senteraweb, our online HVAC portal, where we already made a limited number of specific firmware version available, used in typical HVAC applications like destratification. The only thing that needs to be done is to select the appropriate functionality on the solution page of our website and download the firmware. No additional programming is required. TCMF8 is also available - for AC fan speed control.

Wartungsgeräte Druckluftaufbereitung, Zubehör

This circular motorised damper is suitable for ducts with 125 mm. The position of the damper blade can be set via Modbus RTU communication or a 0-10 V signal. The enclosure has an airtightness class D according to EN1751. To ensure this classification aluminium tape should be wrapped on the seam between damper/duct. The unit needs 24 VDC supply voltage. We recommend using Sentera 24 VDC power supplies with RJ45 connector. They are protected against overload, overvoltage and short circuit. Once installed the device is ready for use. The default settings will suffice for most applications. If you do need to change some parameters, this can be done via Modbus RTU communication.

Air purification unit for cleaning room air The Pro air purification unit cleans the air inside the room. The Pro unit is used for the protection of vulnerable (immune-compromised) patients, protection against infectious patients, the elimination of aspergillus during renovation works, and for the upgrading of air quality in operating theatres, ICUs, isolation rooms. The Pro unit gives immediate results (within 20 minutes max) and once deployed maintains integrity of the air quality at all times. The life-time of the high efficiency particulate air filter inside the unit is therefore largely extended. The prefilters are supplied in packages and are easily changed.

Opstijging van vocht door capillariteit, die vaak “capillaire opstijging” genoemd wordt, is een natuurlijk fysisch verschijnsel dat vaak voorkomt in oude gebouwen. Deze wordt gekenmerkt door breuklijnen die onder de woning aanwezig zijn (zie onderstaand schema). Het water dat in deze breuklijnen loopt, creëert door wrijving een elektrische lading van 50 tot 500 millivolt. Deze capillaire spanning voert het bodemwater (+) in opgaande lijn naar de muren (-) (zie bovenstaand schema) Het is aangetoond dat de watermoleculen dipolen vormen (zoals magneten) die zich zo richten dat ze zich door de muurporiën heen oprichten via een fysiek verschijnsel dat capillariteit genoemd wordt. De capillaire opstijging onderscheidt zich door de aanwezigheid van minerale zouten in de muren van het type nitraat (afkomstig uit dierlijke uitwerpselen) en sulfaat (afkomstig uit de rots)

Fluidamp Valve, 3-Way, Metric

Galvanisierte Druckluftleitungen

Remote controllers with key switches or with key switches and screen-displays for permanent 100 % security, used with all MedicCleanAir units. Remote controller RC 200 with key switches and screen-displays Integrated function keys for selecting mode. Constant pressure difference display. Illuminated display for operating data recognition. Key switch for secure functional change. Secure operation by qualified personnel only. Choice of incremental speed option. Setting for required pressure difference (automatic at Step 4 with ISO unit). Choice of filter test duration (for PRO air purification unit at level 4). Alarm function (visual and acoustic) for pressure difference. Alarm function (visual and acoustic) for filter condition.

Remote controllers with key switches or with key switches and screen-displays for permanent 100 % security, used with all MedicCleanAir units. Remote controller RC 100 with key switches Key switch to select speed. Connects directly to the air purification unit or isolation unit / no seperate power supply needed. Avoids undesirable external use (only hospital staff)

Stepless regulation of EC fans, AC fan speed controllers or frequency inverters is what this potentiometer stands for. It has an off-position and the output value depends on the position of the rotary knob on the front. This potentiometer has a dry contact output that can be used to remotely switch on/off a fan, open/close a damper etc. The dry contact will be open when the know is turned completely counter clockwise. The input voltage for this potentiometer can lie between 0 - 24 VDC. The version handling 0 - 12 VDC is called the MTP-X10K-NA. The splash-proof housing of both potentiometers allows flush (IP44) or surface mounting (IP54).

The Spraystream 50i – 60i – 70i is a dust suppression machine that generates a consistent stream of microdroplets to capture airborne dust particles and to prevent the escape of fugitive dust. This type belongs to the larger range of misting cannons and is mainly used for outdoor misting. The machine is available mobile but can also be mounted. This type is very suitable for demolition work. It can be used for dust- or odoursuppression.

The Spraystream 35i Selfsupporting is a dust suppression machine that generates a consistent stream of microdroplets to capture airborne dust particles and to prevent the escape of fugitive dust. This type of unit is an autonomous misting cannon available in mono- and 3-phase. This misting cannon is very suitable for demolition works where water or electricity is not available. This unit is compact and easily transported.

This controller regulates the fan speed of single-phase motors from 1,5 to 10 A via phase angle control a.k.a. Triac technology. The supply voltage of 230 VAC can be turned off via the illuminated ON/OFF switch on the side of the unit. Via de potentiometer located on the front of the controller you can set the desired fan speed. Minimum speed can be adjusted via an internal trimmer and kickstart/softstart by adding/removing a jumper on the PCB of the controller. This controller is typically used to regulate the speed of AC fans or centrifugal pumps in HVAC systems. The regulator is also available with TK monitoring. This function will deactivate the motor in case of overheating. The code for this type of regulator suitable for 1,5 A is ITRS-15-DT.

Pre-filtration filters on the outside of the unit Indoor work leads to an increased concentration of aspergillus. In order to protect the high effiency particulate air filter inside the unit during building activities, pre-filtration frames with filters are added to the outside of the device. The life-time of the high efficiency particulate air filter inside the unit is therefore largely extended. The prefilters are supplied in packages and are easily changed.

The RCDC ACC is designed with optimized key sections and equipment to guarantee a maximized efficiency. The steam flows from the turbine into a steam duct and several manifolds to reach the fin tube bundles. The RCDC ACC is designed in streets sitting on a steel leg system (under structure) raised to allow proper air intake into the forced draft modules of A-shape steelframes supporting the fin tube bundles. Once condensed the steam is collected by gravity into a condensate tank located underneath or in the close vicinity of the ACC. The efficiency of the steam condensation process is guaranteed using appropriate and reliable vacuum units. RCDC guarantee the complete system and undertake integral studies related to the ducts and manifolds, the steel leg system and the pipe work and other special studies as appropriate.

Air purification unit for cleaning room air The Pro air purification unit cleans the air inside the room. The Pro unit is used for the protection of vulnerable (immune-compromised) patients, protection against infectious patients, the elimination of aspergillus during renovation works, and for the upgrading of air quality in operating theatres, ICUs, isolation rooms. The Pro unit gives immediate results (within 20 minutes max) and once deployed maintains integrity of the air quality at all times. Pre-filtration filters on the outside of the unit Indoor work leads to an increased concentration of aspergillus. In order to protect the high effiency particulate air filter inside the unit during building activities, pre-filtration frames with filters are added to the outside of the device. The life-time of the high efficiency particulate air filter inside the unit is therefore largely extended. The prefilters are supplied in packages and are easily changed.

Mounting Bracket Kit Notes Flat bracket designed to mount Clippard 2010, 2011-1, 2012 and 2013 valves. See Catalog: Page 146

This self-calibrating CO2 sensor measures CO2 as well as temperature, relative humidity and ambient light conditions. It needs a 24 VAC supply voltage. This sensor can also directly control an EC-fan, AC fan speed controller or frequency inverter. It has 1 single analogue / modulating output depending on the highest measured value for temperature, humidity or carbon dioxide. If you only want to use it for measuring CO2, you can deactivate the temperature or humidity measurement. The FCMFX-series are available for different types of supply voltages such as 24 VDC, 24 VAC/VDC or 230 VAC. All version have 3 LEDS on the frontpanel showing whether the measured value is within or out of range. Additionally they are available in a version with audible alert. All parameters are accessible via Modbus RTU. This sensor doesn't need to be configured. Once installed it's ready for use.